Honda outboard service/repair manual – Seloc | 4-stroke | 4 stroke | Table of Contents PDF file | 2 hp – hp – 4 hp – 8 hp – 40 hp – 50 hp – 75 . Clymer Honda Outboard Marine service and repair manuals are written with model specific coverage for your Honda Outboard Marine. From basic service and. View and Download Honda Outboard Motor BFA owner’s manual online. Honda Power Equipment Outboard Motor Owner’s Manual. Outboard Motor.

Author: Dinris Zulkitilar
Country: Tunisia
Language: English (Spanish)
Genre: Career
Published (Last): 4 March 2018
Pages: 365
PDF File Size: 1.89 Mb
ePub File Size: 7.16 Mb
ISBN: 551-6-46987-573-2
Downloads: 82423
Price: Free* [*Free Regsitration Required]
Uploader: Darr

Refuel carefully to avoid spilling fuel.


The engine exhaust from this product contains chemicals known to the State of California to outboad cancer, birth defects, or other reproductive harm. Enter honea from picture: Shallow Water Operation LAUNCHING To raise the outboard motor out of the water while the engine is stopped and the boat is moored, or for maximum clearance when beaching or launching, use the power tilt switch on the engine pan to tilt the Fuel filter or fuel tank clogged.

Damage to the power tilt system may occur.

You may purchase them from your Honda marine dealer. Overheat Indicator Comes On And Engine Speed Is Limited If the engine protection system remains activated after 30 seconds, return to the nearest boat landing, and have the outboard motor inspected by an authorized Honda marine dealer.


Panel-mount Type The emergency stop switch clip and lanyard system is a safety device that will stop the engine if you fall away from the controls while operating the boat.

Reassemble the strainer body and the cup. Do not try to remove the mud guard clip with f orce without raising the inner part of the mud guard clip.

Clean the oil filter mounting base, and coat the rubber seal of the new oil filter with clean engine oil. Propeller Replacement Propeller Replacement Before replacing the propeller, remove hondq clip from the engine stop switch to prevent any possibility of the engine being started while you are working with the propeller.

To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions.

Thoroughly clean the water separator cup. Power Tilt Switch The tilt lock lever is used to support the outboard motor in the fully-raised position. Use the minimum throttle opening necessary to operate the boat at a safe trolling speed.

The propeller blades may have sharp edges, so wear heavy gloves to protect your hands. Possible Cause Fast idle lever raised side-mount type. Reassemble the water separator body and the cup. When the engine starts, release the key, allowing it to return to the ON position. Be sure to observe the following when servicing the spark plugs. Remove the old fuse by removing two 5 mm screws.

Use only a genuine Honda oil f ilter or a f ilter of equivalent quality specif ied f or your model. Check to be sure there are no fuel leaks before starting the ownerd. Congratulations on your selection of a Honda outboard motor.


Honda Four-Stroke Outboard marine manuals

Never refill the fuel tank inside a building where gasoline fumes may reach mamual or sparks. If a fuse is blown, install a replacement fuse of the same specified rating. Don’t have an account? Old gasoline will cause hard starting, and it leaves gum deposits that clog the fuel system. Remove the dipstick and wipe it clean. Kutboard want to help you get the best results from your new outboard motor and to operate it safely.

You can be burned or seriously injured when handling fuel. Hard starting or stalling after starting. Got it, continue to print. Bad fuel; boat stored without treating oners draining gasoline, or refueled with bad fuel.

To remove the mud guard clips, raise the inner part of each mud uonda clip with a screwdriver, then pull out the clips. Fuel filter or fuel tank filter clogged. Understand the use of all controls. Correction Leave fast idle lever OFF p.

Water accumulation in the water separator can cause loss of power or hard starting.