Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.
|Published (Last):||28 November 2015|
|PDF File Size:||16.10 Mb|
|ePub File Size:||18.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
The following are some examples of applications for which particular attention must be given. Any exceptions to this rule are indicated in Safety Precautions in individual product information. Use a soft, dry cloth to clean the Sensor. d3c-vs1g
Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch
Be sure to connect or disconnect the connector after turning OFF the Sensor. Ambient Conditions Do not use this Sensor in the following locations. Please know and observe all prohibitions of use applicable to the products.
Please notify us before copying or reproducing this catalog in e3v-vs1g manner, for any other purpose. Countermeasure Concept Use a Sensor with the interference prevention function. This may weaken performance. If the Sensor does omronn operate, check the following points. If copying or transmitting this catalog to another, please copy or transmit it in its entirety.
Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch | eBay
Type of noise Noise intrusion path and countermeasure Before countermeasure Noise enters from the noise source through the frame metal. Optical energy does not act as an ignition source, thus there is no danger of explosion or fire. Separate the noise source and the Sensor to a distance where noise does not affect operation. Light may enter e3c-vz1g if the Sensors are separated by more than the sensing distance.
Mutual Interference Prevention Polarizing Filter: For this type of application, separate the Sensors by at least 1. The lens, however, is plastic. Exceptions are indicated in Safety Precautions in individual product information. Power Supply Types An unsmoothed full-wave or half-wave rectifying power supply cannot be used. Use the following methods to attach and remove Fiber Units. Secure the connector cover by hand. Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function.
Close mounting of Sensors is possible by alternating the Emitters with the Receivers in a zigzag fashion up to two Sensors. It is our practice to change model numbers when published ratings or features are changed, or when signi?
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. The following measures can be taken to avoid mutual interference. EE11 Check the parallel movement distance range in the catalog, verify the set distance between adjacent Sensors, and install the Sensors accordingly at a distance at least 1.
Insert a shield copper plate between the Sensor and the noise omdon e. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers.
Strong, conductive electrical wire 2 x 0. Power line Work Required for Unconnected Leads Unused leads for self-diagnosis outputs or other special functions should be cut and wrapped with insulating tape to prevent contact with other terminals.
These E3c–vs1g are designed for use in applications for sensing workpieces and workers that do not affect safety. This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance.
Be sure to read Safety Precautions on page 4. Insert a capacitor, etc. Separate Sensors to distance where interference does not occur. They are rather e3cv-s1g from samples taken from production lots, and are provided for reference as guidelines.
This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Precautions for Safe Use To ensure safety, always observe the following precautions. Be sure to insert a load omrln connecting the power supply. The axis perpendicular to the center of the lens.
Cable Tensile Strength When wiring the cable, do not subject the cable e3cvs1g a tension greater than that indicated in the following table. Organic solvents will dissolve the surface. Systems, machines, and equipment that could present a risk to life or property.
OMRON E3C-VS1G Photoelectric sensor
Do not subject a shielded cable or coaxial cable to tension. If Sensors are mounted in opposite each other, slant the Sensors as shown in the following diagram.
AC 2-wire Sensors Example: