e No part of this standard may be reproduced without the prior permission of DIN Deutsches Institut für Normung e.V., Berlin. In case of doubt, the. Buy DIN POLYETHYLEN COATINGS OF STEEL PIPES AND FITTINGS – REQUIREMENTS AND TESTINGS from SAI Global. DIN () Polyethylene coatings on steel pipes and fittings – Requirements and testing. Be notified when this Standard is updated or amended – Add.
|Published (Last):||8 March 2007|
|PDF File Size:||7.21 Mb|
|ePub File Size:||11.32 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard is also available to be included in Standards Subscriptions.
Thus, you can be sure that the pipe is completely protected. The present edition of DIN not only covers fields of application that are not dealt with in DIN EN ISO and DIN ENit also takes into consideration the current state of the art, not only as regards the tests and test frequencies specified here for the first time, but also as regards various product requirements.
Dln is your terms of payment 9 A: The 3067 is to be cooled after application to avoid unwanted deformation during transport.
DIN 30670 seamless coating pipe with Polyethylene coatings
Epoxy layer will not shift at the stages of levelling and shrinking during dun mounting. This test has therefore been specified here to evaluate surface preparation. The specimen shall be supported in such a manner that its elastic response is eliminated. Depending on the nominal size, there are different minimum values for the normal total coating thickness n. Then, make another cut perpendicular to the axis of the previous cut to isolate the strip and lift a length of about 20 mm from the pipe.
Made In China din coating pipe. Your Alert Profile lists the documents that will be monitored. The surface of the counter electrode shall be a least 10 cm?. You can ensure product safety by selecting from certified suppliers, including 31 fin ISO, 14 with Other, and 4 with ISO certification. The difference of the two glass transition temperatures should comply with the dij of the raw material manufacturer. During base designing the necessity diin provide high resistance to mechanical loads – impacts, pressing in and rubbing, was considered.
For three-layer coatings, the epoxy resin and adhesive layers at the pipe ends shall be removed to at least 80 mm from the welding bevel. Need more than one copy?
Heat-shrinkable sleeve “CANUSA GTS-PE 3L”
This also applies for single-layer sintered polyethylene coatings. The peel strength of the polyethylene coating shall be determined using the test assemblies shown in Figures D.
High performance GTS-PE system is developed so that its operating characteristics are not worse than the characteristics of 3-layer base coating.
There are two kinds of procession by winding-wrap and full-coated. 3670 transportation, measures shall be taken to prevent damage to the steel pipes and fittings or to the coating.
Prior to coating application, the metal surface of the steel pipe shall be free of all contaminants and deleterious matter such as dirt, oil, grease, weld beads, etc. DIN 3 layers polyethylene coating Spiral welded pipe Chinese supplier.
API 5L Coating standard: The adhesive can be applied either as a powder or by extrusion.
DIN PE coatings Furthermore, a penetrometer with a dial gauge having an accuracy of 0,1 mm is needed. On each pipe being inspected carry out at least 12 measurements.
Coating pipe is the pipe that is by the processing after the corrosion, which can effectively prevent or don the steel pipe occurs in the course of transport and chemical or electrochemical reaction corrosion phenomena. Tubing and Casing Coupling. Stainless Steel Welded Pipe. If the document is revised or amended, you will be notified by email.
Experience gained in the transport and ein of pipes and pipelines with polyethylene coatings has shown that a high bond strength is necessary to reduce possible mechanical damage to the pipes. Other design temperatures may be agreed between the purchaser and the coater. Care shall be taken that coating samples are free of adhesives.
Catalogue — Ruscomposite JSC
GTS-PE is developed as per unique technology of adhesion directly to main PE coating that provides characteristics not worse than the main coating. Using a suitable tool, chip off a sufficiently large area of the coating around the drilled hole. Table 1 — Types of coating Type Design temperatures for sintered polyethylene coatings Design temperatures for extruded polyethylene coatings Area of application N from?
Blast cleaning and any necessary subsequent work shall not result in the reduction of the minimum wall thickness specified in the technical delivery standards for the steel pipe. The measurements shall be made at points distributed along four equally spaced longitudinal lines at the intersection with three equally spaced circumferential lines and at a distance of at least mm from the end of the coating.
DIN 3PE coating steel pipe.