CCNA 3 Final Exam Answers (v+v) – Scaling Networks 1. A network designer is considering whether to implement a swit. View Test Prep – -CCNA 3 Final Exam Answers vv60 Scaling Networks (1).pdf from S at Deakin. CCNA 3 Final Exam Answers CCNA 3 Final Exam V Answers only computer 4 CCNA 2 Final Exam V Answers computer 3 and RTR-A CCNA 1 Chapter 10 V Answers computer 4.

Author: Volabar Tujin
Country: Malaysia
Language: English (Spanish)
Genre: Business
Published (Last): 1 May 2008
Pages: 47
PDF File Size: 20.94 Mb
ePub File Size: 8.86 Mb
ISBN: 891-5-25786-976-5
Downloads: 76164
Price: Free* [*Free Regsitration Required]
Uploader: Najin

October 17, at 3: Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical network. However, hosts B and D cannot ping each other. It is plain wrong. Configure cvna switch with the same VTP domain name as other switches in the network.

SSH encrypts only the username and password when logging in. SW1 is configured with native vlan10 so to change it to would enable the connectivity for hosts on vlan Outside electrical interference has been eliminated.

Data traffic passes untagged through the phone to the switch. Power cycle the switch to clear all dynamically learned addresses.

finxl The answer should be: The link between Switch1 and Switch2 is up but not trunked. The command copy running-config startup-config should be used to save the changes on the switch. Reply Marcelo Soares says: Conversely, if an untagged frame is received on a trunk port, the frame is associated with the Native VLAN for this port.


Reset the VTP counters.

Which two statements are true about the operation of the interfaces? The configuration is appropriate for a router-on-a-stick network design.

CCNA 3 v Exam Answers score %

April 27, at 2: The switch port is configured for auto duplex and the PC is configured for full duplex. BPDU frames multicast frames broadcast frames Layer 3 packets Using the command copy tftp: Downloading to the startup-config requires the switch to be reloaded in order for the configuration to take effect. Physically connect to the access point and then reboot the computer to launch the configuration software.

Download The Cisco Report Today!

CCNA 3 Final Exam V Answers

May 5, at 5: Users A and B are reporting intermittent connectivity problems. It is participating in the election process by forwarding the BPDUs it receives.

Default native vlan is vlan1. What should be done to remedy the problem? November 13, at 2: Allow all VLANs on the trunk link. Configure the new office default gateway to What will commonly cause this problem? On the basis of the outputs that are provided, which group of users will be able to communicate with the users on VLAN 10 on SW1? Switches S2 and S3 are properly connected using an ethernet cable.


An administrator is troubleshooting a PC on the network which is suffering from slow and intermittent connectivity. What is the purpose of the Spanning Tree algorithm? The PC is set to full duplex.

What are two benefits of the IEEE SW1 drops the traffic because it is untagged. July 13, at 2: The ip domain-name command must also be entered in line configuration mode for the vty lines. Traffic on native vlan is left untagged. Why do you need a router if there both on the same vlan? December 14, at 9: What is the cause of this problem?

CCNA 3 Final Exam V4.0 Answers

Whenever an inter-switch link fails, the network takes nearly a minute to completely converge. There is a native VLAN mismatch. Refer to the exhibit. Introducing Routing and Switching in the Enterprise Version 4.

What will fix the problem? Documents Flashcards Grammar checker.