Page 1. CR R. Page 2. Block E-1 CYLINDER/CYLINDER HEAD. Refnr Part Number. Part Description. Unit Qty. Repair Qty. Price SEK. (excl. VAT). 1. View and Download Honda CRR owner’s manual online. CRR Motorcycle pdf manual download. Does anyone have a pdf of the 04 manual or if not, does anyone know http://

Author: Saramar Migis
Country: Belgium
Language: English (Spanish)
Genre: Literature
Published (Last): 18 August 2008
Pages: 166
PDF File Size: 6.13 Mb
ePub File Size: 19.37 Mb
ISBN: 261-1-71866-414-6
Downloads: 95225
Price: Free* [*Free Regsitration Required]
Uploader: Tuzragore

Remove the RC valve cover bolts and wire clamp. Install the side covers, side cover bolts and collars. Service or disposal should only be done by your loose swingarm bearings. Be sure to grease the air cleaner flange where it contacts the manul cleaner housing. Don’t have an account? Place your CR on the optional Honda work- 4.


Page 45 Teeth Teeth bly, hold the chain ends against adjacent rear used in preference to motor oil. Indicates a strong possibility of severe personal injury or death if instructions are not followed.

Both lighter and heavier than standard springs are available for the shock and fork from your authorized Honda dealer. Turning the adjuster screw one full turn clock- stages with separate adjusters.

CR “A” clyinder vs “B” cylinder. Starting The Engine ance by paying extra 2040 to how you ride during 2. Make several photocopies of this page for future use Page I would luv a copy of that manual if i could.


Remove the float bowl plug, float bowl screws and holder. Shift the transmission into neutral. Slip the cylinder over the top of the piston while fied torque. Page 62 Pour the recommended fork oil into the outer tube. Page 1 of 2.

Honda CR250R 2004 Owner’s Manual

Turn the fork damper upside down for 10 minutes and NOTE: Chassis Adjustments For Track Conditions 7. Rear Suspension Service or disposal should only be done by your loose swingarm bearings. Lubricate any sliding surface, O- rings, and seals before reassembling. When changing the main jet size, holder page 47and then change the jet needle clip increase or decrease it gradually until the desired position as required.

PM me if you want one or just reply and i will PM with info. Page 60 Remove the handlebar holder nuts, washers, rubber Remove the disc cover by removing the two bolts. Check the drive chain rollers for wear. Tighten the top bolts first. Its getting hot so if you wanna ride lets make it soon and go hit up beumont or somethin. I am in Ontario Canada and would gladly pay for the shipping and even a little extra for your trouble Ive ridden for a few years but never had a decent bike without cable brakes, kickstand or a good motor until now!

Remove the alternator cover and keep it handlebar thoroughly, and apply a light coating of all electrical connections.

Thoroughly lubricate the cable 2. Amount of fork oil left in the fork unit: To print the manual completely, please, download it. Page of 89 Go. Turn the fuel valve OFF. Install the dowel pins. Turn the fuel valve ON. Install the hanger plate and tighten the bolts. Therefore, the fuel filter Pro Honda HP2 2-stroke oil or its equivalent, sea next larger slow jet is needed.


Install the collars and shroud A bolts. Definetly hit up beumont I havent been there in over 6 months going through withdrawls. General Service Information Check spoke tension and rim lock nut securely.

Brakes Rein- is probably air in the brake system and it must fr250 bled.

Do not let the clips fall into the crankcase. American honda motor co.

Check for deteriora- determine the pad wear. Page 35 Do not let the clips fall into the crankcase.


Remove the water hose and left radiator from the Drain the radiator coolant page Fill the fuel tank with pre-mixed fuel page 2. Remove the fork protector and brake caliper. Dirtbike Forums Portal – Top.

Also i have a question, besides the oil to gas mix of Honda White Lithium Grease, or an equivalent, is handy for this because any dirt that penetrates this sealing area will show up clearly. Pour the fork oil from the oil hole of the fork damper. Check spoke tension and rim lock nut securely.